Collaborative Information Site

User Profile @diyobd2

follow: RSS


diyobd2's Posts - Page 8

SuperOBD SKP-900 program 2013 Nissan Slyphy remote key (Success)

This is a success case tested by diyobd2.fr engineers for sharing: SuperOBD SKP-900 can program 2013 Nissan Slyphy remote key successfully! The detailed operation steps are as follows.

Step1. Connect SKP900 Key Programmer with car. Turn ignition on. Choose “Immobilizer” then “Nissan”

Choose “New Structure”

And “Smart Key”

Step2. You can see “Keyless System”, press Enter button to select. Then “Choose OBD2 Adapter”: choose YES.

Choose “Read BCM Code” function. Insert key and turn ignition on.

SKP900 read BCM code out.

Step3. Go back to function menu and choose “Activate Steering Lock”. Turn ignition off then press Enter button.

Now it will remind you after activate steering lock all keyless will close, press Enter button to confirm.

Input pin code.

Steering Lock activate successfully!

Step4. Put the new remote key close to car Start button meanwhile press the Start bu

continue reading
1 visits |0 Comments|Reply

I-2015 Actia Multi diag works no issues on BMW E90, bmw mini

Something interesting on Actia multi diag access j2534 interface. share it here. Maybe helpful to you.

First I used Muti diag software on a BMW MINI 2011. One client took his car to my garage because the airbag light constantly flashed. I tested it with VCI but no code stored. I checked some other parameters and all fine. Then I disconnected the battery, and did a battery reset for half an hour. The SRS light went off finally. 

 

 

 

 

Then I run muti-diag access on BMW E90. Read and cleared fault codes of engine injection mevd17kw n55. Lots of sreenshots i took this time, for share. It will better to help all know Muti-diag.

 

http://obd2francais.blogspot.com/2016/10/i-2015-actia-multi-diag-works-no-issues.html

continue reading
3 visits |0 Comments|Reply

Where to get the CHEAPEST SPX AUTOBOSS OTC D730 scanner

How much is the AUTOBOSS OTC D730 automotive diagnostic scanner from China?

At diyobd2.fr, the high-quality OTC D730 scan tool price is €869. It’s GENUINE.

Source: http://www.diyobd2.fr/wholesale/spx-autoboss-otc-d730-automotive-diagnostic-scanner-with-built-in-printer.html

Is it ok to get a cheap OTC D730? Any quality issues?

It is definitely quality-guaranteed with QC marks.

 

QC mark is inter-laboratory quality assessment scheme to promote quality immunohistochemistry. The programme measures staining quality as finial out come to assess techniques used and reagents employed. It tries to provide recommendation for improvement and give optimum protocol.

What can SPX AUTOBOSS OTC D730 contribute to auto repairing?

  1. Covers more than 50 vehicle makes
  2. Access to powertrain, chassis and body systems
  3. Quick Test function to test most vehicle systems
  4. Fault codes (DTC’s), Data Stream and Service Reset
  5. Actuations, Adaptations- and Control Module C
continue reading
6 visits |0 Comments|Reply

How to install MPPS V18 software driver on Windows 7

It’s MPPS v18 windows 7 installation manual of mpps software and driver.

 

NOTE:

1 Mpps v18 software only supports windows7.

2 Be sure the driver installation completes, then open the mpps software to use. Otherwise, mpps can not be used.

3 Mpps v18.12.3.8 software only work mpps hardware v1.08.21 (SE134) at http://www.diyobd2.fr/

 

MPPS V18

https://goo.gl/KwUwxT

 

MPPS V18 eu clone installation steps:

Insert CD and open CD Drive (E:) MPPS V18

Copy folder “MPPS V18” to local disk C:

Open folder MPPS V18 on C: and send MPPS application to Desktop

Close the system message of driver software installation (not successful)

Open computer management to update driver software of Atm Flash

Browse driver software on computer: ComputerC:MPPS V18Device driver

Install device driver ATM device package

 

Car makes:Mpps v18 car list:

https://mega.nz/#!840nybSY!feEzxiZBAswuda8F-9tcwnnZxmZeJcRTE2NSTfYev

continue reading
4 visits |0 Comments|Reply

VVDI PRO VVDIPROG v4.3.1 replace Porsche BCM 2M25J CPU

posted by diyobd2 on Oct 25, 2016
tags: VVDI PROG VVDI PROG Programmer v4.4.9

Managed to replace/ change Porsche 2M25J CPU on BCM, with back-up of original D-FLSH and P-FLSH

I first tried it myself.

Rewrite partition for 2M25J

 

If the D-FLSH is 16KúČset EEE partition as 8

 

If the D-FLSH is 32KúČset EEE partition as 0

 

Xhorse VVDI PROG Programmer:

 

Partition division complete. Then write the backup D-FLSH, and then P-FLSH

Finish encryption in the end. Porsche encryption byte: 7D

 

 

However, the BCM cannot work at all. Failed to read data and unencrypt.

Discussed with the engineer, i adopted the method below:

Step 1 - completely clear the encryption

Select the device and clear the encryption fully

 

Then CPU is all cleared. Again divide CPU partition. set the partition as 8

Step 2 - Write D-FLSH

Some data to modify before writing D-FLSH

Find out Line “7FF00” and replace “7D” with “FF”, then write CPU

 

Then perform encryption

continue reading
3 visits |0 Comments|Reply

KTM100 fw V7.003 sw V2.13/ V2.11 ECU Programming Tool Master Use Tips and tokens reset

posted by diyobd2 on Oct 25, 2016
tags: KTAG ktag ktm100 KTM100 7.003

 

When the ECU tunners use Chinese KTAG KTM100 fw V7.003 sw V2.13/ V2.11 ECU programming tool master, what should they pay attention to? Please read following use tips and tokens reset method.

Chinese KTM100 fw V7.003 sw V2.13/ V2.11 use tips:

1. Do not run the original software on our hardware, otherwise the hardware may be damage.

2. Connect to the internet is safe when you run our software on our hardware.

3. KTM100 all options are gray, there are two possible reasons, you may run the original software, or the tokens are used up.

KTM100 get following error message, how to fix?

Possible reason:

The file contained in the TF card is running wrong.

Solution:

Firstly download this file from http://www.chinaautodiag.com/download/ktm-tf-fix.zip, then follow video to reset.

http://www.diyobd2.fr/wholesale/v213-ktm100-ktag-k-tag-ecu-programmeur-firmware-v7003-avec-token-illimite.html

or contact customer service lilas at e-Mail:sales@diyobd2.fr

 

continue reading
6 visits |0 Comments|Reply

3 minutes UPA USB Programmer read Peugeot 307 BSI MC68HC912

This blog is a guide for using UPA USB Serial Programmer to read Peugeot 307 BSI Motorola MC68HC912. It just costs 3 minutes and easy to do!

Step1. Open UPA USB programmer V1.3 software. It will show you the MC68HC912 wiring diagram.

Connect UPA USB programmer with laptop. Then you need to solder and connect cables according to the wiring diagram to connect the other end with Motorola MC68HC912 MCU.

Step2. Choose “MC68HC912DG128” from left side drop down menu. And select “EEPROM” option at right side.

Click “Read” and it will start read MCU.

And then UPA USB programmer read MC68HC912 MCU successfully! Now you can see the Peugeot 307 bsi dump.

continue reading
72 visits |0 Comments|Reply

Which clone ECU programmer can read good EDC17?

posted by diyobd2 on Oct 22, 2016
tags: Fgtech galletto v54 KESS V2 KTAG MPPS V16

Kess v2 + Ktag read and program Bosch EDC17

 

Ktagkess v2FgTech galletto v54MPPS V16...are all good at Bosch EDC17? Tips are here for good ECU programmers (esp. Ktag and kess) to read EDC17.

 

Kess v2 will programunprotectedBosch EDC17's via OBD.

If the EDC17 ECU is protected, then Ktag can be used to program in boot mode.

Some ECU's can beunlocked, in boot mode with Ktag and then programmed with Kess.kess v2 obd reads are often partial,

Ktag reads are normally full reads.

 

If you want to program EDC17's then I would suggest buying Kess v2 and Ktag, together they are great tools.

 

KESS V2 + EDC17

 

KTAG + EDC17

 

continue reading
8 visits |0 Comments|Reply
[]